[转贴]Surefire Stratum XM-L Mod
本帖最后由 joeqiu88 于 2011-10-3 22:12 编辑多谢WEIJIANG兄弟提醒：
credit：
来自http://thebrightsideforums.com/
论坛
Hi Guyshttp://thebrightsideforums.com/images/smilies/wink2.gif
This Stratum of mine is hard to sell so what the heck I decided to mod it. The LED is an XML T6 1D bin which is of a neutral tint.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum01.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum02.jpg
To my suprise I manage to open the head easily by twisting. Not as bad as the L1 which needs to be heated up. The red stuff on the thread is the thread locker.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum03.jpg
And then I used my 6P/C2 Xeno bezel removal tool to remove the bezel. Quite easy. Here you can see the various components in the head.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum04.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum05.jpg
The head bottom side looks the same like the L1.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum06.jpg
Ok...off to the clamp for LED removal. Desoldered the LED and I use my favourite Leatherman to remove the LED. LED is a K2 TFFC. Correct me if I'm wrong.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum07.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum08.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum09.jpg
Now the head is bare but needed cleaning. I used a plain screw driver to remove residual epoxy. Then I used ArctiClean Thermal Material Remover and Thermal Surface Purifier
to clean any unwanted inpurities on the head and also the XM-L LED. You can also see the original driver which I'm going to use again later.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum10.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum11.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum12.jpg
Now that everything is cleaned I applied Arctic Alumina 2 Part Thermal Adhesive to the LED. Using the Leatherman plier I carefully placed it down on the head making sure it is center.
You will notice that I used plenty of masking tape around the head. This is to avoid any scratches to the head throughtout the whole process.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum13.jpg
Walla...LED is permanently glued and soldering done.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum14.jpg
I put everything back. I wanted to use the Xeno SS bezel but now that the reflector is raised I am unable to. So I used back the old plastic bezel. Need to find myself a thinner lens.
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum15.jpg
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum16.jpg
Beamshots below at 8 feet from the wall. Remember it's a 3 level light. LOW, MED and HIGH. I'm getting 0.03A, 0.12A and 0.54A respectively at the tail.
Hmmm...how many lumens will that be? Maybe someone can check for me. For sure It's brighter than the original one.
LOW
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum17.jpg
MEDIUM
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum18.jpg
HIGH
http://thebrightsideforums.com/images/spacer.gifhttp://i810.photobucket.com/albums/zz25/LightJunk/Surefire%20Stratum%20XM-L%20Mod/Stratum19.jpg
OK...here is the mysteroius part and I'm baffled. Maybe someone can enlighten me.
I used 2 Surefire CR123A which equals to 6V and I'm stuck at LOW and sometimes the LED flickers. But when I used 2 RCR123A= 7.6V I can get all the 3 modes with no problem at all.
Maybe the emitter change contribute to this but I'm just guessing.
I'm happy with the output. Unfortunately it has a dark cross when lit near up to 2 feet. Further than that the beam has a beatiful hotspot in the center.
No dark cross visible. An LDF lens will definitely smoothen it out.
Hope you guys like the mod.
Cheers,
LJhttp://thebrightsideforums.com/images/smilies/smile.gif 头部可以拧开换电路？有电路仓照片吗？ 这个头散热比KX4强 那电路看起来不错啊 强人动手能力让人佩服！ 佩服啊！ 大开眼界。。。。。。。{:1_268:} oh come on oh come on
time1200 发表于 2011-10-4 05:01 http://www.shoudian.org/images/common/back.gif
元帅早晨~~~~ morning marshal morning 早晨 {:1_266:} {:1_242:}透着放假啊 对呀，没看到原厂电路什么样的。 S2不是头都封住的么？？
光杯设计还不错，至少不是那种三角形的会晃来晃去
但总体结构没啥亮点啊，和jet 3M一个样
页:
[1]