|
|
本帖最后由 夾不死 于 2012-7-4 23:34 编辑
Active Dimming Technology，你懂的。
下面谍照的水印，可无视之，思迈除外。
呵呵，CR2型号的英文用户手册也有(版权归思迈所有)，穿了穿了。
Features
• CREE XP-G (R5) LED
• Maximum output of up to 170 lumens
• Highly effective current circuit board
• High efficiency circuit enables maximum runtime of up to 14 hours
• 3 brightness levels
• Active dimming system with auto-adjust function
• Soft turn-on mode and low illumination for everyday usage
• Convenient one-handed operation
• Board voltage circuit, compatible with primary or rechargeable Li-on batteries
• Reverse polarity protection
• Equipped with integrated lens
• Constructed from aerospace grade aluminum alloy
• Type III military grade hard anodizing
• Special-made rhombic knurling for better grip
• Waterproof in accordance with IPX-8 (2 meters submersible)
• Tail stand ability
Dimensions
Length: 57mm
Head Diameter: 19.8mm
Tail Diameter: 18.5mm
Weight: 19.4g (without battery)
Accessories
Key chain, spare O-ring
Battery Options
Primary Lithium battery
SIZE CR2
Nominal voltage 3V
Usability Y (Recommended)
Brightness & Runtime
HIGH 170 LUMENS 1h
MID 50 LUMENS 4h
LOW 20 LUMENS 14h
69m (Beam Distance)
1200cd (Peak Beam Intensity)
1.5m (Impact Resistant)
IPX-8, 2m (Waterproof AND Submersible)
NOTICE
The stated data has been measured in accordance with the international flashlight testing standards ANSI/NEMA FL1, using one high quality CR2 battery (3V, 850mAh) under laboratory conditions. The data may vary in real-world use due to different battery usage or environmental conditions.
Operation instructions
Battery installation
Insert one CR2 battery
WARNING
Always ensure batteries are inserted with the positive (+) ends pointing toward the flashlight head. If incorrectly installed, the flashlight will not work.
ON/OFF
Turn ON: Rotate the head of the flashlight in a clockwise direction to turn it on.
Turn OFF: Rotate the head of the flashlight in a counter-clockwise direction to turn it off.
Brightness Control
When the flashlight is turned on from off:
• Flashlight will enter high output level when the head is parallel to the floor
• Flashlight will enter medium output level when the head is at 45 degrees
• Flashlight will enter low output level when the head is pointing straight down
Notes:
1. Each time you turn on the flashlight, the SENS Mini built-in acceleration sensor can detect the angle and switch to the appropriate brightness level
2. After the lights is powered on, the sensor will shut off to avoid brightness changing when the user changes the flashlight angle.
Active Dimming Technology
With the flashlight switched off, turn on the light with the head pointed straight up. The light will access the active dimming function immediately. An acceleration sensor is built in the SENS Mini flashlight, which can continuously detect the angle of the light and work with the light’s mico-computer to select the appropriate output. For example, when it detects a parallel position, the built-in micro-computer will assume a higher output is appropriate and increase output to illuminate a longer distance. When it detects a vertical position, micro-computer will decrease output so to save battery life, extending runtime of SENS up to 5-8 times.
Notes:
1. When the flashlight switches from low to high level, the output will increase momentarily, allowing the user to observe distant targets.
2. After the flashlight switches from low to high level, the brightness will decrease slowly to allow the user’s eyes to adapt.
Maintenance
Clean the threads twice a year with a clean cloth and coat with silicone grease.
|
|
IP卡
狗仔卡
发表于 2012-7-4 21:05
置顶卡
喧嚣卡
变色卡
显身卡
